Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.
COMSOL-News-Magazine-2017
COMSOL-News-Magazine-2017-Special-edition-acoustics
COMSOL-News-Magazine-2016

Current Density Distribution and Material Removal Behavior on the Graphite/Iron-matrix Interface in Cast Iron Under Pulse Electrochemical Machining Conditions

O. Weber[1], R. Kollmannsperger[2], D. Bähre[2]
[1]Center for Mechatronics and Automatization, Saarbrücken, Germany
[2]Institute of Production Engineering, Saarland University, Saarbrücken, Germany

The Pulse Electrochemical Machining is especially suitable for the precise production of complex geometric contours with high precision and high surface quality demands in workpieces in series manufacturing. During this process, the negative structure of an electrode is copied to the workpiece without sub-surface damages. An adequate knowledge of the current density distribution and thus of the ...

Heat Generation Modeling of Two Lithium Batteries: from the Cell to the Pack in COMSOL Multiphysics® Software

J. Stoudmann [1], R. Rozsnyo [1], T. Mackin [2], J. Dunning [2]
[1] Haute École du paysage, d'ingénierie et d'architecture, Genève, Switzerland
[2] California Polytechnic State University, San Luis Obispo, CA, USA

A thermal model to predict the heat generation during the charge and discharge of a battery pack is an essential tool to manage the thermal behavior, performance and life of the batteries. In this work, a battery cell is modeled in COMSOL Multiphysics® using the Batteries and Fuel Cells module.

Mathematical Modeling of a Lithium Ion Battery

R. E. White[1], and Long Cai[2]
[1]R.E. White & Associates LLC, Columbia, South Carolina, USA
[2]Department of Chemical Engineering, University of South Carolina, Columbia, South Carolina, USA

The existing lithium ion battery model in COMSOL’s Multiphysics  software is extended to include the thermal effects. The thermal behavior of a lithium ion battery is studied during the galvanostatic discharge process with and without a pulse. The existing lithium ion battery model in COMSOL 3.5a is extended by adding an energy balance and the temperature dependence of properties of ...

Simulation of Cyclic Voltammetry of Ferrocyanide/Ferricyanide Redox Reaction in the EQCM Sensor

H. Kwon, and E. Akyiano
Dept. of Engineering and Computer Science
Andrews University
Berrien Springs, MI

In this paper, the cyclic voltammetry behavior of Ferrocyanide/Ferricyanide, which is commonly used for electrochemical DNA detection experiment, was studied in the commercial EQCM-D setup (Q-sense) using the COMSOL Multiphysics. The model was established in a 3D geometry of QCM liquid cell. The simulation shows depletion of concentration of ferrocyanice following applied electrode ...

Two-Dimensional Simulation of All-Solid-State Lithium-ion Batteries

L. Tong [1],
[1] Keisoku Engineering System Co., Ltd., Chiyoda-ku, Tokyo, Japan

There is great interest in developing all-solid-state lithium-ion batteries. They are ideal micro-power sources for many applications in portable electronic devices, electric vehicles and biomedical engineering. It is known that all-solid-state lithium-ion batteries are often fabricated by thin film methods, with thicknesses in the range of a few micrometers. Since porous electrodes are not ...

Primary Current Distribution Model for Electrochemical Etching of Silicon through a Circular Opening

A. Ivanov [1], U. Mescheder [1],
[1] Hochschule Furtwangen University, Furtwangen im Schwarzwald, Germany

Primary current distribution model for anodization of low-doped p-type silicon through a circular opening in frontside insulating mask is developed. The model is applied in two regimes of the process – pore formation and electropolishing – by definition of current density dependent functions of porosity and dissolution valence based on experimental results. As found also experimentally, ...

Impact of Electrode Surface/Volume Ratio on Li-ion Battery Performance - new

S. Das[1], J. Li[2], R. Hui[1]
[1]University of Kansas, Lawrence, KS, USA
[2]Kansas State University, Manhattan, KS, USA

The adoption of micro- and nanostructured electrodes is a promising technique to improve the performance of Li-ion battery, which increases the electrode surface area and improves the efficiency of ion exchange between the electrode and electrolyte. This performance improvement is supported by the results of our numerical simulation based of a Li+ battery in COMSOL Multiphysics® software. The ...

Large and High Power Cylindrical Batteries - Analysis of the Battery Pack Temperature Distributions Using the COMSOL Multiphysics® and MATLAB® Simulation Softwares - new

O. Capron[1], A. Samba[1], N. Omar[1], H. Gualous[2], P. Van den Bossche[1], J. Van Mierlo[1]
[1]MOBI - Mobility, Logistics and Automotive Technology Research Centre, VUB - Vrije Universiteit Brussel, Brussels, Belgium
[2]Laboratoire LUSAC, Université de Caen Basse Normandie, Cherbourg-Octeville, France

The temperature distributions inside two packs (in-line and staggered) made of large cylindrical lithium iron phosphate cells (of 18 Ah nominal capacity) are analysed in this paper during a 90 A constant discharge current. The analysis of the battery packs temperature distributions is based on the results obtained with a two-dimensional modelling approach. For both packs, the simulations ...

Analysis of Electro-Thermal Hot Spot Formation in Li-Ion-Battery-Cells

W. Beckert[1], C. Freytag[1], T. Frölich[1], G. Fauser[1]
[1]Fraunhofer IKTS, Dresden, Germany

The presented model approach offers a computational efficient tool to analyze the influences of geometrical design details, material selection and operational conditions on the electro-thermal behavior of a full Li ion battery cell geometry. It considers typical aspects as anisotropic winding structure, electro-thermal coupling and nonlinear electrical characteristics for moderate computational ...

Parameter Estimation in a Single Particle Model Using COMSOL Multiphysics® Software and MATLAB® Optimization

B. Rajabloo [1], M. Désilets [1], Y. Choquette [2],
[1] Département de Génie Chimique et de Génie Biotechnologique, Université de Sherbrooke, QC, Canada
[2] Institut de recherche d’Hydro-Québec, Varennes, QC, Canada

When it comes to study the behavior of the secondary batteries, physics-based models are more representative of the real behaviour than equivalent circuit models, especially for the estimation of the life and capacity fading. On the other hand, the complexity and computational cost of sophisticated physics-based models like pseudo two-dimensional (P2D) models justify the use of more simplified ...