R. Jia, J. Hu, X. Xiong
Department of Mechanical Engineering, University of Bridgeport, Bridgeport, CT, USA
Department of Electrical and Computer Engineering, University of Bridgeport, Bridgeport, CT, USA
Plate fin heat exchangers are widely used for heat recovery or cooling purposes in many industries, such as cryogenics, aerospace and automobile industries. This paper developed a numerical model to simulate the heat transfer and fluid flow in a counter flow plate fin heat exchanger and optimize its design parameters. The conjugate heat transfer in the finned plate and fluids in the channels ...
E. Mogilevskiy, R. Ferrer, L. Gaffney, C. Granados, M. Huyse, Yu. Kudryavtsev, S. Raeder, P. Van Duppen
KU Leuven, Instituut voor Kern- en Stralingsfysica, Leuven, Belgium
De Laval nozzles are used in supersonic aerodynamical tubes and engines. They are also employed for the production of cold gas jets to be used in chemical reactions studies. Recently, cold gas jets have been proposed of In-Gas Laser ionization Spectroscopy (IGLIS) The nozzle has a converging and a diverging part with a throat between them. High gas pressure and temperature, and low velocity ...
M.W. Siebert, and P.S. Fodor
Physics Department, Cleveland State University, Cleveland, Ohio, USA
In this work, the fluid flow over a 2D backward-facing step is analyzed in order to provide a case study for the use of different models for the blood dynamic viscosity in COMSOL Multiphysics. Three non-Newtonian models, as well as the Newtonian model are used to study the shear stresses and the reattachment length as a function of the fluid speed. The non-Newtonian models used in this study are ...
R. Kiflemariam, M. Almas, C. Lin
Department of Mechanical & Materials Engineering, Florida International University, Miami, FL, USA
2D steady state heat conduction-electric current model was created in COMSOL Multiphysics® software to study the performance of thermoelectric generator-photovoltaic-thermal (TEG-PVT) system. Four different cases were studied in the paper. In case 1, PV cells without concentrator was simulated while in case 2, concentrator ratio range from 2 to 5 was utilized, In case 3, the convection heat ...
Mitsubishi Turbocharger & Engine Europe, Almere, The Netherlands
This study presents a rotordynamic analysis of a rotor on hydrodynamic bearings using COMSOL Multiphysics®. In this paper, the complexity of the model is gradually increased. Starting point of the analysis is the modal analysis of the rotor in free-free conditions. A Reynolds model is set up to predict the film pressure distribution under shaft loading. Due to the cross coupling terms of the ...
Computation of Velocity, Pressure and Temperature Distributions near a Stagnation Point in Planar Laminar Viscous Incompressible Flow
E. Kaufman, and E. Gutierrez-Miravete
Pratt and Whitney, East Hartford, CT, USA
Rensselaer at Hartford, Hartford, CT, USA
As gas turbine temperatures and component life requirements continue to rise, it becomes increasingly important to have a good understanding of the operating temperatures of their components. The objective of this study was to explorate whether a Hiemenz flow approximation based on measured static pressures near an airfoil leading edge can provide a good estimate of the leading edge heat ...
P. Patel, P. Vaidya, G. Singh
Indian Institute of Technology Bombay, Mumbai, Maharashtra, India
Indian Oil Corporation Limited, Faridabad, Haryana, India
This paper presents a simulation approach to develop a model for understanding the mixing phenomenon in a stirred vessel. The mixing in the vessel is important for effective chemical reaction, heat transfer, mass transfer and phase homogeneity. In some cases, it is very difficult to obtain experimental information and it takes a long time to collect the data. Such problems can be solved using ...
J. H. K. Haertel , K. Engelbrecht , B. S. Lazarov , O. Sigmund ,
 Technical University of Denmark, Roskilde, Denmark
 Technical University of Denmark, Kgs. Lynby, Denmark
1. Introduction The topology optimization method is becoming increasingly popular as a design tool for multiphysics systems [1,2]. Topology optimization of fluid-thermal systems has been presented for example in  for forced convective heat transfer and in  for natural convection problems. In this work, topology optimization including density filtering and projection is applied to ...
COMSOL Multiphysics® Simulation of 3D Single-Phase Transport in a Random Packed Bed of Spheres - new
Department of Chemical Engineering, Worcester Polytechnic Institute, Worcester, MA, USA
Packed beds are important in the chemical industries. Computational fluid dynamics (CFD) can simulate detailed flow and scalar transport in packed beds for improved understanding and quantitative information. We present simulations of single-phase gas flow, conjugate heat transfer and isothermal dispersion of mass in a 3D model of a randomly-packed bed (tube-to-particle diameter ratio = 5.96) of ...
P. K. Bahumanyam
University of Alabama in Huntsville, Huntsville, AL, USA
Viable design alternative for the existing and fast growing UAVs which are optimized for unmanned flight is of great demand. Designing of a small scale UAV alternative to the AAI Aerosonde UAV has been considered changing the wing tail configuration of the vehicle analyzing both structural and aerodynamic performance improvements using COMSOL Multiphysics® software.