Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.
COMSOL-News-Magazine-2017
COMSOL-News-Magazine-2017-Special-edition-acoustics
COMSOL-News-Magazine-2016

AlN/ZnO/Silicon Structure Combining Surface Acoustic Waves And Waveguiding Layer Acoustic Wave

O. Legrani[1], O. Elmazria[1], S. Zhgoon [2], L. Le Brizoual[3], and A. Bartasyte[1]
[1]Institut Jean Lamour, CNRS-Nancy University, Vandoeuvre lès Nancy, France
[2]Moscow Power Engineering Institute, Krasnokazarmennaja, Moscow, Russia
[3]Institut des Matériaux Jean Rouxel, Université Nantes, CNRS, Nantes, France

In this work, the theoretical study for the realization of waveguiding layer acoustic waves devices based on AlN/IDT/ZnO/Silicon structure using the modeling software COMSOL Multiphysics (2D) is presented. The effect of thicknesses of AlN and ZnO thin films on the evolution of frequency response, phase velocity and electromechanical coupling is studied. The adequate structure is determined for ...

Shear Induced Detachment Of Microorganisms Attached To A Plane Wall

B. Boulbène, J. Morchain, and P. Schmitz
Université de Toulouse, NSA, UPS, INP, LISBP, Toulouse, France

We present numerical results involving microorganisms adhering to a plane surface submitted to a shear flow. The purpose is to have a better understanding of the removal mechanisms occurring during the cleaning in place of food processing equipments. The biological cell, i.e. the microorganism, is modelled as a rigid obstacle embedded in the bottom wall of the fluid domain. Shear induced ...

Stress Distribution in Masonry Walls, Loaded in Plane, Simulated with COMSOL

A.T. Vermeltfoort, and J. van Schijndel
Eindhoven University of Technology, the Netherlands

The tensile strength of masonry is relatively low compared to its compressive strength and is affected by the direction of the joints and their filling. In masonry with modern thin layer mortar (joint thickness 3 to 5 mm) sometimes the head joints are left open. A total of 13 model-walls was built and for each model four general purpose mortar combinations and three thin layer mortar ...

Simplifying A Model Of Short Subsequent Sections Containing A Common Detailed Cross-Section

J. Krah
AkerSolutions, Fornebu, Norway

In COMSOL Multiphysics it is possible to implement and simulate several independent models in parallel. This can be meaningful when the different models are coupled to each other by some kind of interaction. If a part of the geometries is identical in all models, this part can be reduced in that it is implemented in only one of the geometries. In the other geometries only its solution towards ...

A Methodology For The Simulation Of MEMS Spiral Inductances Used As Magnetic Sensors

S. Druart, D. Flandre, and L.A. Francis
Université catholique de Louvain - ICTEAM, Louvain-la-Neuve, Belgium

In this paper, a methodology to simulate the electric behavior of spiral inductances is presented and discussed. All the methodology is built with the COMSOL software used with the Matlab scripting interface and then allows performing fully parameterized simulations. The program architecture is explained and is used to simulate two applications. The first calculates the voltage induced by an ...

Thermally Induced-Noise Reduction Using an Electrostatic Force Feedback

H. Lee, and J.V. Clark
Purdue University, West Lafayette, IN, USA

In this paper we present a method to mitigate the effect of thermally-induced noise in Micro-Electro-Mechanical Systems (MEMS) through a force feedback circuit. Inherent noise-induced vibrations, which would be inconsiderable in macro scale, are considered as a limitation in micro- and nano- scale since it diminishes the high performance of MEMS devices. For instance, depending on the stiffness ...

Upgrading the HFIR Thermal-Hydraulic Legacy Code Using COMSOL

I.T. Bodey[1], R.V. Arimilli[1], and J.D. Freels [2]
[1]The University of Tennessee, Knoxville, TN, USA,
[2]Oak Ridge National Laboratory, Oak Ridge, TN, USA

Modernization of the High Flux Isotope Reactor (HFIR) thermal-hydraulic (TH) design and safety analysis capability is an important step in preparation for the conversion of the HFIR core from a high enriched Uranium (HEU) fuel to a low enriched Uranium (LEU) fuel. Currently, an important part of the HFIR TH analysis is based on the legacy Steady State Heat Transfer Code (SSHTC). The SSHTC is a ...

Surface Aeration System Modeling using COMSOL

G. Selembo, P. Selembo, J. Stanton, and G. Paulsen
University of North Carolina
Charlotte, NC

Surface aeration systems are used in the wastewater treatment industry for the transfer of oxygen in the activated sludge process. These systems are capital intensive and also require a significant amount of energy to operate. Scale-up and design of these systems is largely empirical, and due to the size of these systems, modifications for experimental testing can be economically prohibitive. ...

Evaluation of Tensile Modulus of Carbon Nanotube Bundle Based Composite with Interface Using Finite Element Method

M. S. Islam, F. O. Riktan, S. C. Chowdhury, M. M. R. Chowdhury, and S. Ahmed
Bangladesh University of Engineering & Technology (BUET)
Dhaka, Bangladesh

Carbon Nanotubes (CNTs) have remarkable mechanical, thermal and electrical properties. The properties of CNTs depend on atomic arrangement (how the sheets of graphite are rolled), the diameter and length of the tubes and morphology of nanostructure. In this paper effective elastic properties of CNT based polymer composites are evaluated using a square Representative Volume Element (RVE) in ...

Simulating Organogenesis in COMSOL

D. Iber, D. Menshykau, and P. Germann
ETH Zürich
Department of Biosystems Science and Engineering
Basel, Switzerland

Organogenesis is a tightly regulated process that has been studied experimentally for decades. Computational models can help to integrate available knowledge and to better understand the underlying regulatory logic. We are currently studying mechanistic models for the development of limbs, lungs, kidneys, and bone. We have tested a number of alternative methods to solve our spatio-temporal ...