S. Kesari, A. Pandit, K. Mishra, Kaushal B. K.
Electronics and Communication Engineering, Nitte Meenakshi Institute of Technology, Bangalore, India
The MEMS microphone is also called microphone chip or silicon microphone.The pressure sensitive diaphragm is etched directly into a silicon chip by MEMS techniques and is usually accompanied with integrated preamplifier. Most MEMS microphones are variants of the condenser microphone design. The device consists of a polysilicon diaphragm suspended over a single crystal silicon backplate ...
P. Pianko-Oprych, E. Kasilova, Z. Jaworski
West Pomeranian University of Technology, Faculty of Chemical Technology and Engineering, Szczecin, Poland
Micro-tubular Solid Oxide Fuel Cells (mSOFC) are attracting more and more interest as new generation of energy conversion devices. Although commercial applications still suffer from high costs, there is a need for further improvement of the cell performance, durability and start-up. To resolve those challenges, knowledge of the distributions of species concentration, temperature and current ...
M. Freda, A. Giannetti, L. Lattanzi, S. Luperi
Centro Sviluppo Materiali, Rome, Italy
The electrochemical pickling of steel has two main purposes: 1) To remove thermal oxide; 2) To dissolve chromium-depleted layer, to reinstate the corrosion-resistant properties of the stainless steel; A reliable, flexible and robust 3D model has been made for simulating the steel electrochemical pickling. This process is modeled as a multiphysics system for the current control. The model ...
H. Fuqua, G. Delory, I. de Pater, R. Grimm
University of California - Berkeley, Space Sciences Lab, Berkeley, CA, USA
University of California - Berkeley, Berkeley, CA, USA
Southwest Research Institute, Boulder, CO, USA
Electromagnetic sounding measurements utilize magnetic induction to constrain the interior geophysical properties of planetary bodies. Under some conditions, the Earth’s moon can be approximated by the response of a conducting sphere in a vacuum. Transient magnetic fields originating from the sun can interact directly with the moon, producing eddy currents that generate an induced magnetic ...
A. Fayolas , M.G. Sanku, M. Pascoa, M. Xynou
KTH Royal Institute of Technology, Stockholm, Sweden
The objective of the study is to investigate the chiral separation of Tröger’s base enantiomers using batch chromatography. Because of its resolution, chromatography is often the preferred method for chiral separations. The separation of Tröger’s base is resolved by using the COMSOL Multiphysics® software. It is modeled by one dimension geometry, having the length of the column set and computed ...
A.R. Sánchez-Guitard, E. Ruiz-Reina
University of Málaga, Málaga, Spain
In this work, we study the design of a new integrated system for Solar Water Heating that combines the solar thermal energy collection (primary circuit) with the heat storage (secondary circuit) into the same device. We have performed different finite element method simulations using COMSOL Multiphysics®, for solving the equations of heat transfer (conduction and convection) and those of fluid ...
Modeling and Simulation of the Rapid and Automated Measurement of Biofuel Blending in a Microfluidic Device under Pressure Driven Flow using COMSOL Multiphysics®
Sanket Goel, Venkateswaran PS, Rahul Prajesh, Ajay Agarwal
University of Petroleum & Energy Studies, Bidholi, Prem Nagar, Dehradun, India
CSIR - Central Electronics Engineering Research Institute,(CSIR-CEERI) Pilani, India
• Real-time detection and monitoring of bio-fuel blend-ratio and adulterated automobile fuels by a reproducible micro-fabrication process in a cost-and-time efficient manner. • COMSOL Multiphysics® simulations and modelling of Viscosity based Laminar Flow inside a Y-shaped Micro-fluidic Device. • Design and Fabrication of a polymer Y-shaped Micro-fluidic Device to work as Micro-Viscometer for ...
Calculation in Coupling Coefficient of 1.3μm Quantum Dots Distributed Feed Back Laser with Half Etched Mesa Structure
Keishiro GOSHIMA et al.
Aichi Institute of Technology, Toyota, Aichi, Japan
Quantum Dots (QDs) laser is expected to have a low threshold current density and high thermal stability. We propose the QDs laser with the half-etched mesa distributed feedback (HEM DFB) structure. We accurately calculated the coupling coefficient in a HEM waveguide using the finite element method (FEM).
Analysis of Heat Transfer in a Complex Three Dimensional Structure Fabricated by Additive Manufacturing - new
C. Settle, K. Hoshino
Biomedical Engineering Department, University of Connecticut, Storrs, CT, USA
The goal of this study was to create a three dimensionally designed biomedical device with multiple functionalities and analyze its simulated heat transfer. The device would be fabricated through additive manufacturing; specifically electron beam melting (EBM). EBM has a feature size constraint of 1 mm (acceptable for this design) and is only capable of manufacturing titanium alloys ; a ...
K. Karthikeyan , L. Sujatha
Rajalakshmi Engineering College, Chennai, Tamil Nadu, India
This paper presents the design and simulation of micromixer for Lab-On-Chip (LOC) applications. There are two types of micromixers: one is an active micromixer and another one is a passive micromixer. This paper investigates microfluidic flow characterization and mixing rate of two fluids in a micro- channel. Understanding the microfluidic flow at the micro channel is a develop methods of mixing ...