Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.
COMSOL-News-Magazine-2017
COMSOL-News-Magazine-2017-Special-edition-acoustics
COMSOL-News-Magazine-2016

Heat Transfer and Phase Change Simulation in COMSOL Multiphysics® Software

N. Huc [1]
[1] COMSOL France, Grenoble, France

This session is devoted to phase change modeling in heat transfer simulations. The great interest in phase change comes from the outstanding thermal performance that it enables in particular for cooling or thermal protection applications. Alternatively, phase change can induce most of the energy cost in drying or cooking applications. In all of these cases, a thermal analysis is required to ...

Models of Simple Iron Cored Electromagnets - new

J. Mammadov[1]
[1]University of Manchester, Manchester, UK

This report mainly discusses the implementation and results of a project proposal, “Modelling using Finite Element Methods”. The report is devoted to implementation, which is a model of an electromagnet. The software tool that is used to model the electromagnet is COMSOL Multiphysics®, a commercial FEA package provided by the University of Manchester, Computer Science School. Additionally, the ...

Simulation of PTFE Billet Sintering using COMSOL

A. Roday, and P. Nicosia
Garlock Sealing Technologies
Palmyra, NY

Sintering is an important step in the manufacturing of polytetrafluoroethylene (PTFE) billets. The challenge in heating large billets stems from the inherent low thermal conductivity of PTFE. Existing literature suggests determining maximum heating rate experimentally using recommended guidelines. This paper uses COMSOL to aid in optimizing the temperature profile required for a particular ...

Sensitivity Analysis of Different Models of Piezoresistive Micro Pressure Sensors

S. Meenatchisundaram[1], S. M. Kulkarni[2], S. Bhat
[1]Department of Instrumentation and Control Engineering, Manipal Institute of Technology, Manipal, Karnataka, India.
[2]Department of Mechanical Engineering, National Institute of Technology, Surathkal, Karnataka, India.

Piezoresistive pressure sensors have received much attention over the years because of low cost, simple measurement techniques, etc. There is a challenge in design with respect to appropriate positioning, shape and temperature compensation. Different models of piezoresistive pressure sensors are proposed to enhance its sensitivity in terms of output voltage. This paper aims in sensitivity ...

Thermal Management of Li-ion Battery Packs - new

D. Adair[1], K. Ismailov[2], Z. Bakenov[3]
[1]School of Engineering, Nazarbayev University, Astana, Kazakhstan
[2]CPS, Nazarbayev University, Astana, Kazakhstan
[3]Institute of Batteries, Astana, Kazakhstan

A design for the thermal management of the media used for packing Li-ion batteries used in hybrid and electric vehicles has been developed. The design satisfies all thermal and physical issues relating to the battery packs used in vehicles such as operating temperature range and volume, and, should increase battery life cycle and charge and discharge performances. Particular attention was ...

Study of Stent Deformation and Stress Developed at Different Stent Deployment Pressures

K. Basu[1], P. Ghosh[2], A. Chanda[1]
[1]School of Bio Science and Engineering, Jadavpur University, Kolkata, West Bengal, India
[2]Jadavpur University, Kolkata, West Bengal, India

According to clinical reports, cardiovascular disease has become a major global healthcare problem. The deposition of fats, cholesterol etc. at the arterials walls causes thrombus formation leading to stenosis and arterial blockage. To tackle this, along with arterial bypass, the use of Cardiovascular Stent is considered promising and effective (in single vessel and bi vessel diseases). While ...

Heat Transfer Modeling and Analysis of a Rotary Regenerative Air Pre-heater

R. K. Krishna, R. Ramachandran, and P. Srinivasan
Birla Institute of Technology and Science
Pilani
Rajasthan, India

An attempt has been made to sustain the efficiency of an air pre-heater(APH) in the long run. The APH is modeled using COMSOL Multiphysics in 3D and fed with real life conditions. Upon Heat transfer analysis, the temperature profile was found out and from that, the regions undergoing maximum thermal fatigue stress was identified. The plates of the APH to the periphery are subjected to maximum ...

Multiphysics Topology Optimization of Heat Transfer and Fluid Flow Systems

E. Dede[1]
[1]Toyota Research Institute of North America, Ann Arbor, Michigan, USA

This paper is focused on topology optimization of heat transfer and fluid flow systems for multiphysics objectives. Specifically, COMSOL Multiphysics software is coupled with a method of moving asymptotes optimizer in a custom COMSOL / MATLAB script. Various physical process including conduction, convection-diffusion, and Navier-Stokes flow are considered. To illustrate the method, a standard ...

Analysis of Hydrodynamic Plain Journal Bearing

Ravindra Mane[1], Sandeep soni[1]
[1]Department of Mechanical Engineering, Sardar Vallabhbhai National Institute of Technology, Surat, Gujarat, India

This paper presents the 3D model of hydrodynamic plain journal bearing using COMSOL Multiphysics®. Using 3D Model, pressure distribution in plain journal bearing is obtained by steady state analysis of plain journal bearing. Generalized Reynolds equation is used for analyzing hydrodynamic journal bearing by COMSOL Multiphysics® as well as by analytical method by applying Sommerfeld boundary ...

Fluid-Structure Interaction Model of Active Eustachian Tube Function in Healthy Adult Patients

F. Sheer[1], and S. Ghadiali [1,2]
[1]Mechanical Engineering Department, Lehigh University, Bethlehem, PA, USA
[2]Department of Biomedical Engineering, Ohio State University, Columbus, OH, USA

The Eustachian Tube (ET) is a collapsible tube that connects the middle ear to the nasopharynx. Dysfunction in the ET leads to a disease called Otitis Media. Our goal is to develop and use fluid-structure interaction (FSI) models of ET opening phenomena to better understand what factors contribute to ET dysfunction in certain patients. We model the ET in COMSOL using geometric data obtained ...