Multi-Objective Optimization of a Strip-Fin Microchannel Heatsink: Integrating COMSOL Multiphysics with modeFRONTIER
A. Clarich, R. Russo, and N. Fateh
Esteco North America, Miami, FL, USA
For this work the multi-objective design environment modeFRONTIER was integrated with COMSOL, bringing the advantages of multi-objective optimization to multiphysics simulations. Practically any commercial analysis tool (such as COMSOL) or in-house code can be integrated within modeFRONTIER’s framework. In the case of the direct approach, modeFRONTIER determines the configurations to be ...
P. Mikulski, K. Mcilhany, and R. Malek-Madani
United States Naval Academy
Here we present and discuss numerical solutions to the paraxial wave equation using COMSOL (2D, PDE, General Form, time-dependent analysis). Ultimately, the goal is to extend this treatment of free-space beam propagation to the case of propagation through a medium that is non-uniform and subject to non-linear effects where the beam itself is modifying the properties of the medium in which it is ...
X. Ma, M.B. de Rooij, and D.J. Schipper
Materials Innovation Institute, Enschede, The Netherlands
University of Twente, Enschede, The Netherlands
This paper describes the use of COMSOL Multiphysics® to determine the shear layer thickness in thin–section aluminum extrusion, based on the minimum work criterion. The studied two aluminum alloys are AA 6063 and AA 7020. The results show that a continuous shear layer featuring shear localization due to localized thermal softening is not possible to form under typical thin&ndash ...
A. Weddemann, and V. Thümmler
Bielefeld University, Germany
ALE-methods are frequently used to solve systems of partial differential equations (PDEs) on moving domains. The main idea of these methods is to incorporate the time evolution of the domain into the equations. However, the motion of the domain with respect to time induces convective fluxes in the resulting equations. These can lead to stability problems of the numerical method if they become ...
P. Franciosa and S. Gerbino
Faculty of Engineering, University of Naples Federico II, Napoli, Italy
Faculty of Engineering, University of Molise, Campobasso, Italy
Tessellated models are more and more used in several engineering fields. The need to use such models to quickly perform computer simulations related to coupled physical phenomena, implies the use of dedicated software, allowing to solve, into an integrated environment, multiphysics problems. In the present work, COMSOL Multiphysics® has been used and its ability to handle tessellated models ...
H. Karakuzu, M. Dubov, S. Boscolo
 Aston University, Birmingham, UK
We present an optimization procedure to improve the propagation properties of the depressed-cladding, buried micro-structured waveguides formed in a z-cut lithium niobate (LN) crystal by high repetition rate femtosecond (fs) laser writing. It is shown that the propagation wavelength for which the confinement losses of ordinary (O) and extraordinary ordinary (E) polarizations are below 1 dB/cm ...
University of Leeds, Leeds, United Kingdom
Nowadays all branches in modern science and industry tend to solve ever complicating problems. As the result the computational time increases considerably and it become very important to reduce the processing time and use available resources more efficiently. Parallelizing problem proves itself as efficient way to overcome the described problem. In the poster we compare different methods of ...
J. E. Toney
Pennsylvania State University Electro-Optics Center, Freeport, Pennsylvania, USA
We demonstrate the use of Comsol Multiphysics with Matlab to model signal generation in wide-bandgap semiconductor radiation detectors. A quasi-hemispherical detector design is compared with a simple, planar detector. Results show that the quasi-hemispherical design can simply and effectively compensate for the poor hole transport of most compound semiconductor materials.
A. Atalla, and A. Jeremic
McMaster University, Hamilton, Ontario, Canada
The inverse diffusion problems deal with the estimation of many crucial parameters such as the diffusion coefficient, source properties, and boundary conditions. Such algorithms are widely applied in many design problems in different physical, chemical, and biological fields. Recently, the estimation of the boundary properties, of the diffusion process, have attracted researchers. We first ...
H. Cabrera, D. A. Zanin, L. G. De Pietro, A. Vindigni, U. Ramsperger, D. Pescia
Laboratory for Solid State Physics, ETH Zürich, Zürich, Switzerland
In our recent experiments we are revisiting the topografiner technology for the imaging of surface topography with a resolution of a few nanometers. In these new technique called Near-Field Emission Scanning Electron Microscopy (NFESEM), low-energy electrons are emitted from a polycrystalline tungsten tip via electric-field assisted tunneling. In order to characterize and improve the ...